Epoxy flake coating and metallic epoxy floors in KL, Selangor and Penang: IFS finishes over Rayson primer for homes, garages and showrooms. Quote per sq ft.
We reply within one working day, Monday to Friday.
Rayson-authorised applicators in Kuala Lumpur and the Klang Valley, and Penang. In Johor: Flake and metallic epoxy floors in Johor Bahru.
An epoxy flake floor is an epoxy coat with coloured flakes, or chips, broadcast into it and sealed under a clear coat: a seamless, speckled surface with more grip than plain gloss epoxy. In KL, Selangor and Penang, Rayson-authorised applicators lay IFS Epoxy Flake Lining over Rayson PrimeBond E20.
Photos from IFS
Photos supplied by IFS, not jobs in Malaysia. Your colour, texture and pattern are chosen on a sample board.
Flake for floors that work hard: garages, kitchens, utility rooms, bathrooms and shops, where the speckle hides dust and the texture grips. Metallic for floors that are looked at: living rooms, showrooms, cafés and feature floors, where the flowing, liquid look is the point.
Both are IFS finishes over the same Rayson base, so the choice can change from room to room, and a sample board in your own light settles it.
No. As a finish on bathroom floors and walls it can work, and IFS’s own photos show it there, but a flake coat over a leaking floor still leaks. The waterproofing under the floor is checked first, and where it has failed, the bathroom is waterproofed before any finish.
Some installers sell flake epoxy as toilet waterproofing. Rayson’s position as the maker is plain: waterproofing is a membrane such as SealForce WB20, laid on the screed under the tiles and ponding-tested; flake lining is the surface you see.
Over tiles that are firmly bonded, yes: the applicator taps every tile, takes out hollow ones, fills the grout lines so the grid does not show through, and primes with a bonding primer before the IFS finish.
Floor traps, door clearances and the edge against the next room are checked at the site visit. Tiles that are loose, or that sit on a floor that is still leaking, are dealt with first.
Any epoxy floor scratches under grit and dragged furniture, and epoxy can yellow where strong sun falls on it. Gloss metallic is slippery when wet; IFS metallic finishes also come matte or velvety, and flake lining is slip-resistant.
Felt pads and a mat at the door keep scratches down. Where daylight reaches the floor, the applicator specifies the clear coat the IFS system calls for there, which is why a car porch open to the sky is discussed at the enquiry first.
| Compared on | IFS Epoxy Flake Lining | IFS Metallic Epoxy | Plain epoxy (Rayson FloorGuard R50) | Tiles |
|---|---|---|---|---|
| The look | Speckled flakes in the colours chosen | Liquid, marbled, one of a kind | An even colour | The pattern of tiles and grout |
| Grip when wet | Slip-resistant (IFS) | Gloss is slippery; matte or velvety helps | Texture can be added | Depends on the tile |
| Joints | Seamless | Seamless | Seamless | A grout line at every tile |
| Over existing tiles | Yes, if firmly bonded, with a bonding primer | Yes, if firmly bonded, with a bonding primer | Yes, if firmly bonded, with a bonding primer | Hacked out, or new tiles laid over |
| Best rooms | Garages, kitchens, utility rooms, bathrooms | Living rooms, showrooms, feature floors | Garages, stores and workshops | Anywhere, with grout lines |
A first guide. The applicator confirms the right finish for your room on site.
Flake blend or metallic effect, colour and sheen chosen on a sample board, in the light of your room.
Grinding, crack and joint repair and a moisture check, then Rayson PrimeBond E20; on tiles, grout lines filled and a bonding primer.
The base coat, then the flakes broadcast or the metallic worked by hand, then the clear coat the IFS system specifies.
Walking, furniture and cars follow the cure times on the data sheets; cleaning is explained at handover.
Per square foot, quoted after inspection by the applicator for your area. Five things decide it: the area, the state of the floor (grinding, cracks and moisture), tiles to fill and prime, flake or metallic and the pattern, and the clear coat where daylight falls. Repairs to the floor are priced as their own step. Rayson publishes no price list.
Independent applicators in Kuala Lumpur and the Klang Valley, and Penang, island and mainland. Elsewhere in Selangor is confirmed per enquiry. In Johor: Flake and metallic epoxy floors in Johor Bahru.
The build-up, top to bottom · diagram, not to scale
Firmly bonded tiles: grout lines filled and a bonding primer first.
Rayson PrimeBond E20 is a two-component, medium-viscosity, solvent-free epoxy bonding primer that anchors resin floor systems to concrete, screed, asphalt and prepared metal — on dry or damp substrates.
Specifications →The decorative finish itself is an IFS product, not a Rayson one.
The system is specified by the company that makes the material, and installed by an independent applicator Rayson has authorised, not chosen from whatever a supplier had on the shelf that week.
Every Rayson material on your floor or roof has a published technical data sheet. You can read what went in, and so can your consultant.
Rayson warrants the material as its maker. The authorised applicator, an independent company that contracts with you, warrants the workmanship. Each warranty is issued by the company responsible for it.
The products, data sheets and application methods are the ones Rayson publishes in Singapore. Nothing is rebadged for Malaysia.
Contractors and facility teams buy the same materials direct from the maker, with application guidance. The applicator is there when you want the job done for you.
Each with the Rayson layers it uses
All decorative finishes ↗Seamless IFS MicroCrete® for condo bathrooms, floors and walls, with Rayson waterproofing under every wet area.
Dry rooms: PrimeBond E20 on concrete or screed, or a bonding primer over firmly bonded tiles, in place of the membrane.
Quoted after inspectionThe polished concrete and simen kilat look over the floor you already have: the IFS overlay, or IFS’s polished concrete slab for a new floor.
A new floor: IFS polished concrete slab, at least 25 mm (IFS). Wet areas: the applicator confirms whether SealForce WB20 goes underneath first.
Quoted after inspectionService bays, wash bays and car showrooms: hard-wearing epoxy in the workshop, a colour-stable finish in the showroom.
Wash bays and ramps: R50 broadcast with aggregate. Showrooms: UraForce WB58 topcoat over R50. Heaviest bays: LevelShield SL120.
Quoted after inspectionAn independent, Rayson-authorised applicator in your area: Kuala Lumpur and the Klang Valley, including Petaling Jaya, Shah Alam and Subang Jaya, or Penang, island and mainland. It inspects, quotes, contracts with you and warrants the workmanship; Rayson is not the installer. Elsewhere in Selangor is confirmed per enquiry, and Johor has its own page.
No. Factory and warehouse floors take Rayson’s own industrial systems, such as FloorGuard R50 or LevelShield SL120, specified for forklifts and chemicals. Epoxy Flake Lining and Metallic Epoxy are IFS decorative finishes for homes, shops and showrooms.
Epoxy Flake Lining and Metallic Epoxy are IFS products (Industrial Floor & Systems Pte. Ltd) and carry IFS’s own terms. The primer under them is Rayson PrimeBond E20, with a published data sheet, and the combined build-up is confirmed on a sample board before your job.
The whole job takes several working days, because the primer, the base coat, the flake or metallic coat and the clear coat each cure in turn. Walking, furniture and cars follow the cure times on the data sheets, which the applicator sets out in the quotation.
Three parties, each for its own part: Rayson for its layers as their maker, IFS’s terms for the flake or metallic finish, and the Rayson-authorised applicator for the workmanship. All three are written into the quotation.
Tell us what the surface is, where it is and what it has to withstand. Rayson replies with a system recommendation; for installation, the applicator for your area in Johor, Kuala Lumpur or Penang is introduced to quote the job.
Malaysia launch: 1 March 2027. Enquiries are welcome now; supply, site assessment and installation timing are confirmed for each project.