Workshop and showroom epoxy flooring in Malaysia: FloorGuard R50 for service and wash bays, UraForce WB58 for showrooms, by Rayson-authorised applicators.
We reply within one working day, Monday to Friday.
Rayson-authorised applicators in Johor, Kuala Lumpur and the Klang Valley, and Penang. Materials and data sheets nationwide.
A primed epoxy floor built for vehicles: Rayson specifies FloorGuard R50 over PrimeBond E20, a solvent-free epoxy whose data sheet lists vehicle workshops, garages and ramps, broadcast with aggregate in wash bays. Showrooms take R50 in colour under a non-yellowing UraForce WB58 topcoat.
Mostly because of oil in the concrete. A workshop slab soaks up oil and grease over the years, and a coating laid over it without deep cleaning and grinding lets go. The rest comes from paint used where a floor system was needed.
The survey checks how deep the oil goes; badly soaked patches are cut back and repaired before the primer goes on.
Textured: FloorGuard R50 broadcast with aggregate and sealed with a further coat, the slip-resistant system its data sheet sets out for ramps and wet zones. A smooth gloss floor in a wash bay is slippery the moment it is wet.
The falls to the drains are checked at the survey, because a coating follows the slab and cannot move the water by itself.
Colour and light. Epoxy yellows in sunlight, so a showroom with glass frontage takes FloorGuard R50 in your colour under UraForce WB58, a water-based polyurethane topcoat listed for non-yellowing, abrasion-resistant finishes in commercial interiors.
The colour is chosen on a sample, and the same finish can run into the service reception so the brand looks the same throughout. For a feature floor, an IFS finish such as Metallic Epoxy or polished concrete overlay goes over Rayson primer instead: an IFS product under IFS’s own terms, chosen on a sample board.
Yes, in sections: bays are closed in turn and the floor laid around the lifts and pits. R50 has a pot life of up to 30 minutes at 30 °C and seven days to final cure; each bay returns to service when the specification allows.
Lift baseplates, pits and drainage channels are detailed in the quotation, so the bays go back into use without loose edges.
| Compared on | System | Finish | Why it fits |
|---|---|---|---|
| Service bays and workshops | FloorGuard R50 over PrimeBond E20 | Smooth gloss, or textured | Listed for vehicle workshops, garages and ramps |
| Heavy-duty bays and stores | LevelShield SL120 over PrimeBond E20 | Self-levelling | Listed for maintenance workshops and areas under mechanical loading |
| Wash bays and ramps | FloorGuard R50, broadcast with aggregate | Textured and sealed | Grip when wet |
| Showroom | FloorGuard R50 under UraForce WB58 | Colour-stable topcoat | Non-yellowing in daylight through the glass |
| Feature showroom floor | IFS Metallic Epoxy or polished concrete overlay, over Rayson primer | Metallic, or the raw concrete look | An IFS finish, chosen on a sample board |
A first guide. The specification confirms the system for your vehicles and traffic.
Moisture, bond and oil checks, the lifts, pits and drains, and how the bays are used.
System by zone, colour, details and the data sheets, in writing, with the programme bay by bay.
Degreasing, grinding and repairs, PrimeBond E20, then R50 or SL120, with WB58 in the showroom.
Bays back in service when the specification allows; data sheets in your file.
Per square foot, quoted after a survey. Five things decide it: the area, how much oil is in the slab and how much grinding and repair it needs, the system by zone, the details around lifts, pits and drains, and the bay-by-bay programme. Rayson publishes no price list; contractors with their own crews can buy the systems direct.
Independent, Rayson-authorised applicators in Johor, Kuala Lumpur and the Klang Valley, and Penang. Sites elsewhere are confirmed per enquiry; materials and data sheets are supplied nationwide.
The build-up, top to bottom · diagram, not to scale
Wash bays and ramps: R50 broadcast with aggregate. Showrooms: UraForce WB58 topcoat over R50. Heaviest bays: LevelShield SL120.
Rayson PrimeBond E20 is a two-component, medium-viscosity, solvent-free epoxy bonding primer that anchors resin floor systems to concrete, screed, asphalt and prepared metal — on dry or damp substrates.
Specifications →
Rayson FloorGuard R50 is a two-component, solvent-free high-solids epoxy floor coating that cures to a smooth gloss — or a slip-resistant finish when broadcast with aggregate — for concrete and screed under normal to medium-heavy wear.
Specifications →
Rayson LevelShield SL120 is a solvent-free, two-component, self-smoothing epoxy floor system that delivers a seamless wearing surface with medium to heavy chemical resistance and high mechanical strength.
Specifications →
Rayson UraForce WB58 is a two-component, water-based aliphatic polyurethane dispersion topcoat, crosslinked with a PUR hardener, for abrasion-resistant coloured finishes on concrete, metal and mineral surfaces.
Specifications →The system is specified by the company that makes the material, and installed by an independent applicator Rayson has authorised, not chosen from whatever a supplier had on the shelf that week.
Every Rayson material on your floor or roof has a published technical data sheet. You can read what went in, and so can your consultant.
Rayson warrants the material as its maker. The authorised applicator, an independent company that contracts with you, warrants the workmanship. Each warranty is issued by the company responsible for it.
The products, data sheets and application methods are the ones Rayson publishes in Singapore. Nothing is rebadged for Malaysia.
Contractors and facility teams buy the same materials direct from the maker, with application guidance. The applicator is there when you want the job done for you.
Each with the Rayson layers it uses
All industries ↗Speckled flake and seamless metallic or marbled epoxy floors from the IFS range, laid over Rayson primer.
Firmly bonded tiles: grout lines filled and a bonding primer first.
Quoted after inspectionThe polished concrete look over your existing floor or wall, without breaking it out: the IFS overlay on a prepared base.
Wet areas: the applicator confirms whether a SealForce WB20 membrane goes underneath first.
Quoted after inspectionBasement and covered car park decks, ramps and walkways in condos, malls, offices and factories, with a textured epoxy deck system.
Pedestrian walkways: GripSafe AP12. Open, sun-exposed top decks: outside the current range.
Quoted after inspectionOver a sound, well-bonded coating, after degreasing, grinding and a bond test, yes. Where the old coating is peeling or soaked with oil, it is ground off first, because the new floor is only as good as what it sticks to.
Heavy-duty bays are specified apart, usually with LevelShield SL120 self-levelling epoxy; the survey sets the system against your vehicles and loads.
Rayson warrants the materials as their maker; the Rayson-authorised applicator that lays the floor warrants its workmanship. Both are written into the quotation.
Tell us what the surface is, where it is and what it has to withstand. Rayson replies with a system recommendation; for installation, the applicator for your area in Johor, Kuala Lumpur or Penang is introduced to quote the job.
Malaysia launch: 1 March 2027. Enquiries are welcome now; supply, site assessment and installation timing are confirmed for each project.