Rayson makes the materials. Independent, Rayson-authorised applicators in Johor inspect, quote and install every job with them, and warrant their own workmanship. Pick the job, send three photos, and the applicator comes back with a quotation per square foot.
Rayson membranes
Waterproofing in Malaysia ↗Flat concrete, tiled and metal roofs: the cause found first, then a membrane over the whole roof.
Flat roofs that pond or are walked on: SealForce RC40 polyurea.
Quoted after inspectionThe membrane under the tiles, done once and flood-tested before the tiler starts.
Read the stain first: toilet above, roof, pipe or wall each need a different repair.
Under a roof: a roof membrane instead. A steady drip in any weather: a plumber first.
Quoted after inspectionDamp, peeling, mouldy walls: rain through the render, rising damp or a leak next door.
Water from a wet area behind the wall: that room is re-waterproofed instead.
Quoted after inspectionSurfaces that are rained on and walked on, with a room underneath that must stay dry.
Under new tiles: SealForce WB20 beneath a protected screed.
Quoted after inspectionLarge flat and metal roofs in Johor’s industrial parks, coated without stopping production.
Metal and free-draining roofs: SealForce AC10, over an anti-corrosion primer on metal or AP05 on concrete.
Quoted after inspectionRayson materials
Epoxy flooring in Malaysia ↗Forklift aisles, production floors and loading bays in Johor’s industrial parks, specified by the maker.
Storage halls: FloorGuard R50 roller coat. Hot washdown or spillage: PurScreed PC70.
Quoted after inspectionGarages, kitchens, living rooms and porches: plain coloured epoxy by Rayson, IFS metallic and flake finishes over Rayson primer.
Metallic and flake finishes: IFS Metallic Epoxy or Epoxy Flake Lining, over the same primer.
Quoted after inspectionSeamless, cleanable floors done overnight or between tenancies, with colour that lasts under daylight.
GripSafe AP12 texture at the entrance and wet zones.
Quoted after inspectionRamps, walkways, porches, pool decks and wet rooms made safe underfoot.
Coated floors: quartz broadcast into the epoxy finish. Glazed tiles: a tile treatment, quoted on inspection.
Quoted after inspectionMachining halls, timber stores, packing and container loading, finishing lines and buyer showrooms in the furniture factories of Muar and Batu Pahat.
Timber and board stores: FloorGuard R50. Showroom: R50 under UraForce WB58, or an IFS finish. Finishing lines: after the chemical check.
Quoted after inspectionBy industry, across Malaysia
Johor, Kuala Lumpur and the Klang Valley, and Penang
Industries we cover ↗Hot washdown, wet process and dry store floors for food and beverage plants, with coves and drains detailed.
Dry stores and packing: FloorGuard R50 or LevelShield SL120 over PrimeBond E20. Walls: UraForce WB58.
Quoted after inspectionBasement and covered car park decks, ramps and walkways in condos, malls, offices and factories, with a textured epoxy deck system.
Pedestrian walkways: GripSafe AP12. Open, sun-exposed top decks: outside the current range.
Quoted after inspectionForklift aisles, racking zones and loading bays in warehouses and distribution centres, in self-levelling or roller-applied epoxy.
Racking and storage zones: FloorGuard R50 roller coats. Heavy traffic with spillage: PurScreed PC70.
Quoted after inspectionESD floors, plant rooms, loading bays, car parks and roofs for data centres in Johor and across Malaysia.
Plant rooms and loading bays: LevelShield SL120. Car parks: FloorGuard R50 broadcast system. Roofs: SealForce RC40.
Quoted after inspectionCooking lines, dishwash and prep areas in central, hotel and restaurant kitchens: PU-cement where it is hot, epoxy where it is dry.
Cold prep, stores and corridors: FloorGuard R50 broadcast with aggregate, over PrimeBond E20.
Quoted after inspectionService bays, wash bays and car showrooms: hard-wearing epoxy in the workshop, a colour-stable finish in the showroom.
Wash bays and ramps: R50 broadcast with aggregate. Showrooms: UraForce WB58 topcoat over R50. Heaviest bays: LevelShield SL120.
Quoted after inspectionProduction rooms, clean rooms, device assembly, washdown rooms and stores in pharmaceutical and medical device plants, with smooth, cleanable floors and walls.
Walls: UraForce WB58. ESD assembly: StaticGuard CX90. Washdown rooms: PurScreed PC70.
Quoted after inspectionESD areas, production halls, wet and chemical rooms, warehouses and car parks in electronics and semiconductor plants, zone by zone.
Outside the ESD programme: LevelShield SL120. Wet and chemical rooms: PurScreed PC70. Car parks: FloorGuard R50 broadcast system.
Quoted after inspectionCorridors, service areas, kitchens, laundries, wet rooms, ramps and car parks in hospitals, clinics and care homes, laid in occupied buildings.
Corridors and service areas: LevelShield SL120 or FloorGuard R50. Kitchens and laundries: PurScreed PC70. Walls: UraForce WB58.
Quoted after inspectionClassrooms, corridors, halls, walkways, playgrounds, toilets, canteens and roofs in schools and kindergartens, done in the school holidays.
Walkways, ramps and playgrounds: GripSafe AP12. Toilets: SealForce WB20 under the tiles.
Quoted after inspectionIFS partner range over Rayson layers
About the IFS range ↗Seamless cement finish over floors, walls and showers, with Rayson waterproofing underneath where it is wet.
Dry floors: PrimeBond E20 primer in place of the membrane, or a bonding primer over firmly bonded tiles.
Quoted after inspectionIFS Japanese terrazzo, poured in place, for homes, lobbies and shops, on a base prepared with Rayson materials.
Natural pebbles in clear resin for car porches, paths and pool surrounds, with the waterproofing underneath done first.
Speckled flake and seamless metallic or marbled epoxy floors from the IFS range, laid over Rayson primer.
Firmly bonded tiles: grout lines filled and a bonding primer first.
Quoted after inspectionThe polished concrete look over your existing floor or wall, without breaking it out: the IFS overlay on a prepared base.
Wet areas: the applicator confirms whether a SealForce WB20 membrane goes underneath first.
Quoted after inspectionKuala Lumpur, Selangor and Penang
Through the Rayson-authorised applicators there
Seamless IFS MicroCrete® for condo bathrooms, floors and walls, with Rayson waterproofing under every wet area.
Dry rooms: PrimeBond E20 on concrete or screed, or a bonding primer over firmly bonded tiles, in place of the membrane.
Quoted after inspectionThe polished concrete and simen kilat look over the floor you already have: the IFS overlay, or IFS’s polished concrete slab for a new floor.
A new floor: IFS polished concrete slab, at least 25 mm (IFS). Wet areas: the applicator confirms whether SealForce WB20 goes underneath first.
Quoted after inspectionIFS Japanese terrazzo, poured in place with no grout lines, for homes, lobbies and shops, on a base prepared with Rayson materials.
Speckled epoxy flake and seamless metallic epoxy floors from the IFS range, for homes, garages and showrooms, over Rayson primer.
Firmly bonded tiles: grout lines filled and a bonding primer first.
Quoted after inspectionThe system is specified by the company that makes the material, and installed by an independent applicator Rayson has authorised, not chosen from whatever a supplier had on the shelf that week.
Every Rayson material on your floor or roof has a published technical data sheet. You can read what went in, and so can your consultant.
Rayson warrants the material as its maker. The authorised applicator, an independent company that contracts with you, warrants the workmanship. Each warranty is issued by the company responsible for it.
The products, data sheets and application methods are the ones Rayson publishes in Singapore. Nothing is rebadged for Malaysia.
Contractors and facility teams buy the same materials direct from the maker, with application guidance. The applicator is there when you want the job done for you.
Tell us what the surface is, where it is and what it has to withstand. Rayson replies with a system recommendation; for installation, the applicator for your area in Johor, Kuala Lumpur or Penang is introduced to quote the job.
Malaysia launch: 1 March 2027. Enquiries are welcome now; supply, site assessment and installation timing are confirmed for each project.