Factory and warehouse floors that take forklifts, food-plant and kitchen floors that take hot washdown, clean rooms, ESD floors for electronics plants and data centres, hospital corridors, school classrooms, car park decks, showrooms and home garages. Rayson names the system and supplies it; an authorised applicator in Johor, Kuala Lumpur or Penang quotes and installs it, or your own crew does with our materials.
| The floor | The system | Rayson products | Why |
|---|---|---|---|
| Storage hall, workshop, garage | Roller-applied epoxy, 2 coats | PrimeBond E20 + FloorGuard R50 | Seals and colours a sound slab; add aggregate on ramps for grip. |
| Production floor, forklift aisles, loading bay | Self-levelling epoxy | PrimeBond E20 + LevelShield SL120 | Seamless, hard-wearing, hides a rough slab; medium to heavy chemical resistance. |
| Food and beverage plant, commercial kitchen, chemical plant, hot washdown | Polyurethane-cement screed, 1.5 to 3 mm, layered for heavier duty | PurScreed PC70 | Takes heat, steam cleaning and spillage that stress an epoxy. |
| Car park deck, basement, ramp | Epoxy broadcast with aggregate, sealed | PrimeBond E20 + FloorGuard R50 | Listed for multi-storey and underground car parks; textured for grip. Open, sun-exposed top decks are outside the range. |
| Data hall, electronics, ESD-protected area | Conductive epoxy, 1.0 to 1.5 mm | StaticGuard CX90 | Conductive through its body, laid over earthing points and tested after cure. |
| Pharmaceutical plant, clean room | Self-levelling epoxy, seamless and coved | PrimeBond E20 + LevelShield SL120; UraForce WB58 on walls | Listed for pharmaceutical facilities and clean rooms; smooth, cleanable and solvent-free. |
| Office, showroom, school, retail | Epoxy + water-based PU topcoat | FloorGuard R50 + UraForce WB58 | Colour stays true under daylight; low-odour application in an occupied building. |
| Pedestrian ramp, wet walkway, playground | Anti-slip primer filler | GripSafe AP12 | Builds a quartz texture in one product on concrete or asphalt. |
Each industry has its own page: the floor for every zone, the Rayson system and its data sheet, what to send and what decides the price. Independent, Rayson-authorised applicators install them in Johor, Kuala Lumpur and the Klang Valley, and Penang.
Hot washdown, wet process and dry store floors for food and beverage plants, with coves and drains detailed.
Dry stores and packing: FloorGuard R50 or LevelShield SL120 over PrimeBond E20. Walls: UraForce WB58.
Quoted after inspectionBasement and covered car park decks, ramps and walkways in condos, malls, offices and factories, with a textured epoxy deck system.
Pedestrian walkways: GripSafe AP12. Open, sun-exposed top decks: outside the current range.
Quoted after inspectionForklift aisles, racking zones and loading bays in warehouses and distribution centres, in self-levelling or roller-applied epoxy.
Racking and storage zones: FloorGuard R50 roller coats. Heavy traffic with spillage: PurScreed PC70.
Quoted after inspectionESD floors, plant rooms, loading bays, car parks and roofs for data centres in Johor and across Malaysia.
Plant rooms and loading bays: LevelShield SL120. Car parks: FloorGuard R50 broadcast system. Roofs: SealForce RC40.
Quoted after inspectionCooking lines, dishwash and prep areas in central, hotel and restaurant kitchens: PU-cement where it is hot, epoxy where it is dry.
Cold prep, stores and corridors: FloorGuard R50 broadcast with aggregate, over PrimeBond E20.
Quoted after inspectionService bays, wash bays and car showrooms: hard-wearing epoxy in the workshop, a colour-stable finish in the showroom.
Wash bays and ramps: R50 broadcast with aggregate. Showrooms: UraForce WB58 topcoat over R50. Heaviest bays: LevelShield SL120.
Quoted after inspectionProduction rooms, clean rooms, device assembly, washdown rooms and stores in pharmaceutical and medical device plants, with smooth, cleanable floors and walls.
Walls: UraForce WB58. ESD assembly: StaticGuard CX90. Washdown rooms: PurScreed PC70.
Quoted after inspectionESD areas, production halls, wet and chemical rooms, warehouses and car parks in electronics and semiconductor plants, zone by zone.
Outside the ESD programme: LevelShield SL120. Wet and chemical rooms: PurScreed PC70. Car parks: FloorGuard R50 broadcast system.
Quoted after inspectionCorridors, service areas, kitchens, laundries, wet rooms, ramps and car parks in hospitals, clinics and care homes, laid in occupied buildings.
Corridors and service areas: LevelShield SL120 or FloorGuard R50. Kitchens and laundries: PurScreed PC70. Walls: UraForce WB58.
Quoted after inspectionClassrooms, corridors, halls, walkways, playgrounds, toilets, canteens and roofs in schools and kindergartens, done in the school holidays.
Walkways, ramps and playgrounds: GripSafe AP12. Toilets: SealForce WB20 under the tiles.
Quoted after inspectionJohor. Pasir Gudang, Senai, Tebrau, Ulu Tiram, Kulai, Iskandar Puteri and the Nusajaya and Sedenak tech parks: factories, warehouses, logistics hubs and the plant rooms of new data centres. Further north, the furniture factories of Muar and Batu Pahat. The same applicators do the home garages, kitchens and shop floors in Johor Bahru, Skudai and Gelang Patah.
Penang. The electronics and manufacturing plants of Bayan Lepas, Batu Kawan and Prai, and homes and shops on the island and the mainland.
Kuala Lumpur and the Klang Valley. Factories and warehouses in Shah Alam, Subang Jaya and Petaling Jaya, car parks, shop and mall fit-outs, and condos and landed homes across the city.
See the Kuala Lumpur and Klang Valley and Penang pages. Elsewhere in Malaysia, Rayson supplies materials and specifications to contractors with their own crews.
The whole floor, the worst patch, and anything on it that must come off. Area in square feet and what will run on it.
System, preparation, thickness and the data sheets, in writing. Contractors buying materials get coverage figures and application guidance.
The authorised applicator for your area visits, checks moisture and bond, and quotes the installation per square foot. The quotation, invoice and workmanship warranty are the applicator’s.
Primer, body coat, topcoat, each to the data sheet; foot traffic next day, full load after cure. Rayson warrants the material.
Rayson makes and specifies every layer you see below. The independent, Rayson-authorised applicator inspects your floor, quotes it, installs it and warrants the workmanship. Each job page shows how the work runs, what to send and what decides the price.
Forklift aisles, production floors and loading bays in Johor’s industrial parks, specified by the maker.
Storage halls: FloorGuard R50 roller coat. Hot washdown or spillage: PurScreed PC70.
Epoxy and anti-slip · Rayson materials
Garages, kitchens, living rooms and porches: plain coloured epoxy by Rayson, IFS metallic and flake finishes over Rayson primer.
Metallic and flake finishes: IFS Metallic Epoxy or Epoxy Flake Lining, over the same primer.
Quoted after inspectionSeamless, cleanable floors done overnight or between tenancies, with colour that lasts under daylight.
GripSafe AP12 texture at the entrance and wet zones.
Quoted after inspectionRamps, walkways, porches, pool decks and wet rooms made safe underfoot.
Coated floors: quartz broadcast into the epoxy finish. Glazed tiles: a tile treatment, quoted on inspection.
Quoted after inspectionMachining halls, timber stores, packing and container loading, finishing lines and buyer showrooms in the furniture factories of Muar and Batu Pahat.
Timber and board stores: FloorGuard R50. Showroom: R50 under UraForce WB58, or an IFS finish. Finishing lines: after the chemical check.
Quoted after inspectionDecorative finishes · IFS partner range over Rayson layers
About the IFS range ↗Seamless cement finish over floors, walls and showers, with Rayson waterproofing underneath where it is wet.
Dry floors: PrimeBond E20 primer in place of the membrane, or a bonding primer over firmly bonded tiles.
Quoted after inspectionIFS Japanese terrazzo, poured in place, for homes, lobbies and shops, on a base prepared with Rayson materials.
Natural pebbles in clear resin for car porches, paths and pool surrounds, with the waterproofing underneath done first.
Speckled flake and seamless metallic or marbled epoxy floors from the IFS range, laid over Rayson primer.
Firmly bonded tiles: grout lines filled and a bonding primer first.
Quoted after inspectionThe polished concrete look over your existing floor or wall, without breaking it out: the IFS overlay on a prepared base.
Wet areas: the applicator confirms whether a SealForce WB20 membrane goes underneath first.
Quoted after inspectionYour floor is not listed? Send three photos and the size, and Rayson names the system for it.
Send the floor All jobs in Johor ↗Per square foot, and it depends on three things: how much preparation the slab needs, how thick the system is, and which system it is. A roller-applied coating on a sound slab is the cheapest; a self-levelling floor costs more; a PU-cement screed for a food or chemical plant costs the most and lasts the longest. Rayson does not publish a price list; the authorised applicator for your area quotes after seeing the floor.
An independent applicator in Johor, Kuala Lumpur or Penang, introduced by Rayson. The applicator quotes, invoices and warrants the workmanship. Rayson supplies the material and the specification, and warrants the material. Contractors with their own crews can buy the materials and get application guidance.
Foot traffic is typically possible the next day; forklifts and full chemical exposure wait for full cure, usually several days depending on the product and the temperature. The data sheet of each product gives the figures; the applicator plans the shutdown around them.
Over sound, well-bonded old epoxy, yes, after grinding and a primer. Over tiles, only with a bonding primer and after checking that the tiles themselves are firmly bonded; a loose tile takes the new floor with it. Over new concrete, the slab must have cured and its moisture must be checked first.
Forklift aisles and loading bays: LevelShield SL120 self-levelling epoxy, or PurScreed PC70 where there is hot washdown or chemical spillage. Storage halls and workshops: FloorGuard R50 roller coat, broadcast with aggregate where ramps need grip. Offices and showrooms: R50 with a UraForce WB58 topcoat for colour and UV stability.
Food and beverage plants, commercial and central kitchens, warehouses and logistics, car parks, data centres, workshops and showrooms, pharmaceutical and medical device plants, electronics and semiconductor plants, hospitals, clinics and care homes, and schools and kindergartens, each with its own page and the Rayson system for every zone; furniture factories in Muar and Batu Pahat; and factories, homes, shops and cafés. Showrooms, lobbies and foyers can take an IFS decorative finish. Cold rooms, open, sun-exposed car park decks and operating theatres are outside the current range.
Both. Garages, kitchens, balconies and shop floors in Johor, Kuala Lumpur and Penang are typical home and small-business jobs for the applicators; the same products apply, usually the roller-applied system.
Tell us what the surface is, where it is and what it has to withstand. Rayson replies with a system recommendation; for installation, the applicator for your area in Johor, Kuala Lumpur or Penang is introduced to quote the job.
Malaysia launch: 1 March 2027. Enquiries are welcome now; supply, site assessment and installation timing are confirmed for each project.