Anti-slip walkway or ramp
- Clean, repair and level the surface; stripe-coat edges by brush
- Apply Rayson GripSafe AP12 across the area; overcoat dull patches with a further coat
- Finish with Rayson UraForce HY15 or CourtFlex AC25 in the selected colour
Rayson GripSafe · Acrylic
Rayson GripSafe AP12
Rayson GripSafe AP12 is a one-pack, self-crosslinking acrylic primer filler loaded with 0.5–1.5 mm silicate quartz aggregate that builds an anti-slip texture directly onto concrete and asphalt.
ConcreteCement screed TDS RY-TDS-801
Best for
Best for putting reliable anti-slip texture on walkways, ramps, playgrounds and courts in a single ready-to-use product.
GripSafe AP12 puts the anti-slip aggregate in the can. Instead of broadcasting loose grit into a wet primer, the 0.5–1.5 mm silicate quartz is factory-blended into a self-crosslinking acrylic binder — so every pass lays down a consistent, repeatable texture. It doubles as primer and filler, keying subsequent finish coats.
The cured coat is tough: high abrasion resistance, excellent water resistance, good weather resistance and excellent adhesion to concrete and masonry. It is fast-drying (touch dry in 30–60 minutes at 25 °C), non-yellowing, suitable for interior and exterior use, and low in VOCs at under 50 g/litre.
It applies to asphalt, grey concrete, stone, unglazed tiles and pavers, covering duties from pedestrian walkways and ramps to playgrounds, basketball and tennis courts and cycling paths.
In Malaysia
Supplied by Epovex Coatings Sdn. Bhd., Company No. 202601042128 (1704223-A). The Malaysia launch is scheduled for 1 March 2027; confirm availability and lead time for your project. Installation through an authorised applicator in Johor, Kuala Lumpur or Penang introduced by Rayson, who quotes and warrants the workmanship, or by your own crew with Rayson’s application guidance.
Send an enquiryKey benefits
- Factory-blended 0.5–1.5 mm quartz gives consistent anti-slip texture
- One pack, ready to use — no broadcasting step
- Fast-drying with high abrasion and excellent water resistance
- Non-yellowing, interior and exterior; VOC under 50 g/litre
Recommended uses
- Pedestrian walkways and ramps
- Industrial floors requiring slip resistance
- Playgrounds, basketball courts and tennis courts
- Cycling pathways
Application
- Trowel or squeegee
- Brush for stripe-coating edges
| Specification | Data sheet value |
|---|---|
| Coverage | Theoretical 5–8 m² per litre, subject to substrate porosity and application conditions |
| Mixing | Single component, ready to use; condition material to 15–25 °C before use |
| Drying and curing | Touch dry 30–60 minutes at 25 °C; recoat after 2–4 hours; full cure 1 day |
| Pack sizes | 22 L plastic pail |
Typical systems
Limitations
- Ambient and surface temperature above 10 °C, and at least 5 °C above the dew point
- Surface must be dry, clean and free of loose paint, dust, grease, oil, wax and biological growth
- Neutral colour only — pair with a coloured finish coat where colour is required
- Texture grade is fixed by the factory aggregate blend
Not suitable for
- Smooth decorative finishes — the aggregate texture is the point
- Glazed tiles or non-porous glossy surfaces without specialist preparation
- Heavy forklift traffic areas — use an epoxy or PU-cement system
- Application below 10 °C or onto damp, contaminated surfaces
Jobs and industries
Jobs that use Rayson GripSafe AP12
Rayson-authorised applicators in Johor, Kuala Lumpur and Penang install Rayson GripSafe AP12 on these jobs and in these industries; its layer is marked in each build-up. Each page shows how the work runs, what to send for a quotation and what decides the price.
Jobs in Johor
01 Rayson system
Shop, café and showroom floors
Seamless, cleanable floors done overnight or between tenancies, with colour that lasts under daylight.
- UraForce WB58 topcoat, colour-stable in daylight
- FloorGuard R50 epoxy in the shop’s colour
- PrimeBond E20 epoxy primer
- Concrete floor, degreased and keyed
GripSafe AP12 texture at the entrance and wet zones.
Quoted after inspection 02 Rayson system
Anti-slip floor treatment
Ramps, walkways, porches, pool decks and wet rooms made safe underfoot.
- GripSafe AP12 quartz anti-slip texture
- Concrete or asphalt, cleaned and keyed
Coated floors: quartz broadcast into the epoxy finish. Glazed tiles: a tile treatment, quoted on inspection.
Quoted after inspectionBy industry, across Malaysia
Industries we cover ↗ 03 Rayson system
Car park floors
Basement and covered car park decks, ramps and walkways in condos, malls, offices and factories, with a textured epoxy deck system.
- FloorGuard R50 sealing coat
- FloorGuard R50 broadcast with graded aggregate
- PrimeBond E20 epoxy primer
- Concrete deck, ground and moisture-tested
Pedestrian walkways: GripSafe AP12. Open, sun-exposed top decks: outside the current range.
Quoted after inspection 04 Rayson system
Hospital, clinic and care home floors
Corridors, service areas, kitchens, laundries, wet rooms, ramps and car parks in hospitals, clinics and care homes, laid in occupied buildings.
- Tiles, re-laid after the ponding test
- Tile bed
- SealForce WB20, two coats, turned up the walls
- Screed to falls
- Floor slab
Corridors and service areas: LevelShield SL120 or FloorGuard R50. Kitchens and laundries: PurScreed PC70. Walls: UraForce WB58.
Quoted after inspection 05 Rayson system
School and kindergarten floors
Classrooms, corridors, halls, walkways, playgrounds, toilets, canteens and roofs in schools and kindergartens, done in the school holidays.
- UraForce WB58 topcoat, colour-stable
- FloorGuard R50 epoxy in a colour from the range
- PrimeBond E20 epoxy primer
- Concrete floor, keyed and repaired
Walkways, ramps and playgrounds: GripSafe AP12. Toilets: SealForce WB20 under the tiles.
Quoted after inspection The practical details
Rayson GripSafe AP12: questions people ask
How does GripSafe AP12 differ from broadcasting aggregate?
The quartz is pre-blended into the product, so texture is uniform with no broadcasting, sweeping or wastage — and no thin spots where the grit missed.
Does it need a topcoat?
It works as a stand-alone anti-slip coat in its neutral colour; where colour or extra cleanability is wanted, overcoat with UraForce HY15 or CourtFlex AC25.
How aggressive is the texture?
The aggregate is graded 0.5–1.5 mm — a firm pedestrian anti-slip profile. If you need a specific measured slip rating for compliance, confirm the requirement with our technical team.
Can it go on asphalt?
Yes — asphalt is a listed substrate alongside concrete, stone, unglazed tiles and pavers.
How soon can it be recoated or walked on?
Indicatively touch dry in 30–60 minutes, recoatable in 2–4 hours and fully cured in a day at 25 °C.
Start a conversation / ↗
Send the job, or ask for materials
Tell us what the surface is, where it is and what it has to withstand. Rayson replies with a system recommendation; for installation, the applicator for your area in Johor, Kuala Lumpur or Penang is introduced to quote the job.
Malaysia launch: 1 March 2027. Enquiries are welcome now; supply, site assessment and installation timing are confirmed for each project.