Commercial kitchen flooring in Malaysia: PurScreed PC70 PU-cement for cooking lines and hot washdown, coved and drained, by Rayson-authorised applicators.
We reply within one working day, Monday to Friday.
Rayson-authorised applicators in Johor, Kuala Lumpur and the Klang Valley, and Penang. Materials and data sheets nationwide.
Polyurethane-cement where it is hot and wet: Rayson specifies PurScreed PC70 at 1.5 to 3 mm for cooking lines and dishwash, with coves and drains detailed first. Drier prep areas, stores and corridors can take FloorGuard R50 epoxy, broadcast with aggregate for grip.
Tiles fail at the grout: hot water and fat get into the joints and the tiles loosen and crack. Epoxy fails where it is hot: the epoxy data sheets refer hot washdown and thermal shock to a PU-cement screed, so epoxy on a cooking line is laid outside what it is made for.
A seamless PU-cement floor has no grout lines to open, and its coved edges leave no corner for fat and water to sit in.
Any kitchen floor is slippery under oil and water if it is smooth. The texture for each zone is set in the specification after the survey, to suit the oil, the water and the cleaning, and the finished floor is checked wet before handover.
In the drier prep areas FloorGuard R50 is broadcast with aggregate for grip; on the hot lines, the grip of the finished PC70 floor is checked wet with you before handover.
It depends on the area and the system. PC70 has a short pot life and the data sheet gives seven days to final cure, so kitchens are usually done in sections over closing days or a planned shutdown, agreed before work starts.
A central kitchen that runs every day is split into zones, so production moves from one side to the other while the floor goes down.
The Food Hygiene Regulations 2009 require floors to be kept in good condition, easily cleaned, impervious, non-absorbent, washable, non-toxic and adequately drained (regulation 18), and wall-floor angles to be sealed and coved where necessary (regulation 19(2)).
A seamless floor with coved edges and clean drain details answers both. Falls to the drains are a matter for the slab: where water sits, the falls are built in a screed before the floor goes down.
| Compared on | Rayson system | Build | Why it fits |
|---|---|---|---|
| Cooking lines, woks and fryers | PurScreed PC70 PU-cement | 1.5 to 3 mm, trowelled | Made for hot wet processing and spillage |
| Dishwash and hot washdown | PurScreed PC70 PU-cement | 1.5 to 3 mm, coved at the walls | Hot water and cleaning chemicals every day |
| Cold prep, stores and corridors | FloorGuard R50, broadcast with aggregate | Roller-applied over PrimeBond E20 | Seamless and textured at lower cost |
| Walls | UraForce WB58 hygienic coating | Thin film over a sound, sealed wall | Smooth and washable |
| Walk-in freezers and cold rooms | Outside the current range | Not quoted | No Rayson data sheet covers freezer or cold-room floors yet |
A first guide. The specification confirms each system against your heat, oil and cleaning.
What comes up, moisture and bond tests, the drains and falls, and the hours the kitchen can close.
Zones, systems, coves and drain details and the data sheets, in writing, with the programme around service.
Old tiles and coatings removed, repairs, coves and drain edges, then PC70 and R50 at the data-sheet build.
Back in service when the specification allows; the floor checked wet with you, and the data sheets in your file.
Per square foot, quoted after a site survey. Five things decide it: the area and how it splits into hot and dry zones, what comes up (old tiles, screed, coatings), the coves, drains and plinths to detail, the falls to the drains, and the hours the kitchen can close. Rayson publishes no price list; contractors with their own crews can buy the systems direct.
Independent, Rayson-authorised applicators in Johor, Kuala Lumpur and the Klang Valley, and Penang. Sites elsewhere are confirmed per enquiry; materials and data sheets are supplied nationwide.
The build-up, top to bottom · diagram, not to scale
Cold prep, stores and corridors: FloorGuard R50 broadcast with aggregate, over PrimeBond E20.
Rayson PurScreed PC70 is a four-part, water-based polyurethane-cement self-smoothing screed installed at 1.5–3 mm for medium to heavy-duty industrial floors with high chemical resistance.
Specifications →
Rayson FloorGuard R50 is a two-component, solvent-free high-solids epoxy floor coating that cures to a smooth gloss — or a slip-resistant finish when broadcast with aggregate — for concrete and screed under normal to medium-heavy wear.
Specifications →
Rayson PrimeBond E20 is a two-component, medium-viscosity, solvent-free epoxy bonding primer that anchors resin floor systems to concrete, screed, asphalt and prepared metal — on dry or damp substrates.
Specifications →
Rayson UraForce WB58 is a two-component, water-based aliphatic polyurethane dispersion topcoat, crosslinked with a PUR hardener, for abrasion-resistant coloured finishes on concrete, metal and mineral surfaces.
Specifications →The system is specified by the company that makes the material, and installed by an independent applicator Rayson has authorised, not chosen from whatever a supplier had on the shelf that week.
Every Rayson material on your floor or roof has a published technical data sheet. You can read what went in, and so can your consultant.
Rayson warrants the material as its maker. The authorised applicator, an independent company that contracts with you, warrants the workmanship. Each warranty is issued by the company responsible for it.
The products, data sheets and application methods are the ones Rayson publishes in Singapore. Nothing is rebadged for Malaysia.
Contractors and facility teams buy the same materials direct from the maker, with application guidance. The applicator is there when you want the job done for you.
Each with the Rayson layers it uses
All industries ↗Hot washdown, wet process and dry store floors for food and beverage plants, with coves and drains detailed.
Dry stores and packing: FloorGuard R50 or LevelShield SL120 over PrimeBond E20. Walls: UraForce WB58.
Quoted after inspectionSeamless, cleanable floors done overnight or between tenancies, with colour that lasts under daylight.
GripSafe AP12 texture at the entrance and wet zones.
Quoted after inspectionRamps, walkways, porches, pool decks and wet rooms made safe underfoot.
Coated floors: quartz broadcast into the epoxy finish. Glazed tiles: a tile treatment, quoted on inspection.
Quoted after inspectionNot as a rule. PurScreed PC70 is laid on prepared concrete, so the tiles come up and the slab is repaired first.
Yes: central kitchens, hotel and restaurant kitchens, and catering and canteen kitchens.
Rayson warrants the materials as their maker; the Rayson-authorised applicator that lays the floor warrants its workmanship. Both are written into the quotation.
Tell us what the surface is, where it is and what it has to withstand. Rayson replies with a system recommendation; for installation, the applicator for your area in Johor, Kuala Lumpur or Penang is introduced to quote the job.
Malaysia launch: 1 March 2027. Enquiries are welcome now; supply, site assessment and installation timing are confirmed for each project.