Rayson FloorGuard R50 epoxy floor paint and PrimeBond E20 primer, sold direct across Malaysia, with a step-by-step guide to applying it from the data sheets.
We reply within one working day, Monday to Friday.
Supplied across Malaysia through Epovex Coatings Sdn. Bhd. Rayson-authorised applicators in Johor, Kuala Lumpur and the Klang Valley, and Penang.
Epoxy floor paint is a two-component resin coating, mixed by weight, rolled over an epoxy primer, that hardens into a smooth, hard-wearing, easy-to-clean floor. Rayson FloorGuard R50 goes on in two coats over PrimeBond E20 and reaches its final cure in seven days.
FloorGuard R50 goes on at 0.3 to 0.5 kg/m² a coat in two coats, so one 20 kg set covers about 20 to 33 m² of floor. PrimeBond E20 primer covers 6 to 8 m² per kg, and one 20 kg set primes about 120 to 160 m².
For example, a 40 m² garage (about 430 sq ft) needs 24 to 40 kg of R50, two sets, and 5 to 7 kg of primer. The primer set is far more than a small garage needs, so give the area when you order and Rayson works out the quantities for you.
No. Ordinary paint dries as its solvent evaporates; epoxy is two components mixed by weight, FloorGuard R50 at 4:1, that harden by chemical reaction. Once mixed it must be used within 30 minutes at 30 °C.
That is why it is mixed with a mechanical mixer for 2 to 3 minutes, by weight rather than by eye, and only as much as can be rolled out in that time. A wrong mix never cures fully.
On a covered porch or in a garage, yes. On a porch open to the sun, no: the R50 data sheet says it is not for exterior UV-exposed surfaces, because epoxy yellows and chalks outdoors.
For an open porch, ask when you order; Rayson suggests another system for outside surfaces, and the applicator can look at it.
Not with this system. PrimeBond E20 is made for concrete, screed, sound old epoxy, asphalt and prepared metal, not glazed tiles. An epoxy floor over tiles needs a bonding primer and an applicator.
For a home floor over firmly bonded tiles, a Rayson-authorised applicator lays an IFS flake or metallic finish over a bonding primer, with the build-up confirmed on a sample board.
| Compared on | Do it yourself with Rayson materials | A Rayson-authorised applicator |
|---|---|---|
| Suits | Garages, store rooms, workshops, indoor or covered floors | Factories, forklift aisles, wet process, large areas |
| Preparation | A hired floor grinder and an industrial vacuum | Diamond grinding or shot blasting, crack and joint repair |
| Moisture check | A plastic sheet taped down overnight as a first check | Measured with a meter; E20 takes a damp but not wet slab, 5% or less |
| Warranty | Rayson warrants the material | Material by Rayson; workmanship by the applicator |
| Price | Materials only, quoted per order | Per square foot, after inspection |
A first guide. If in doubt, send a photo of the floor and Rayson tells you which suits.
Concrete at least 28 days old, moisture 5% or less, no rising damp; a plastic sheet taped down overnight is a first check, and condensation under it means wait. Mix and cure between 10 °C and 35 °C.
Grind the concrete clean and open, remove oil and old paint, repair cracks and vacuum all the dust; the data sheet asks for a sound surface, at least 1.5 N/mm² in a pull-off test.
Mix parts A and B at 2:1 by weight with a mixer for 2 to 3 minutes, roll at 6 to 8 m² per kg, and use within 30 minutes at 30 °C.
Mix 4:1 by weight for 2 to 3 minutes, roll 0.3 to 0.5 kg/m² a coat, the second coat within the time the data sheet gives; broadcast aggregate into the first coat on ramps for grip. Final cure in seven days.
Materials are quoted per order, by the set: tell Rayson the area and the floor, and you get the number of FloorGuard R50 and PrimeBond E20 sets, the coverage and the price, with supply and delivery confirmed for your order. Applied by a Rayson-authorised applicator, it is quoted per square foot after inspection instead. Rayson publishes no price list.
Materials and data sheets go anywhere in Malaysia. For the installation, Rayson-authorised applicators work in Johor, Kuala Lumpur and the Klang Valley, and Penang.
The build-up, top to bottom · diagram, not to scale
Ramps: aggregate broadcast into the first coat for grip. Porches open to the sun: not this system.
Rayson FloorGuard R50 is a two-component, solvent-free high-solids epoxy floor coating that cures to a smooth gloss — or a slip-resistant finish when broadcast with aggregate — for concrete and screed under normal to medium-heavy wear.
Specifications →
Rayson PrimeBond E20 is a two-component, medium-viscosity, solvent-free epoxy bonding primer that anchors resin floor systems to concrete, screed, asphalt and prepared metal — on dry or damp substrates.
Specifications →The system is specified by the company that makes the material, and installed by an independent applicator Rayson has authorised, not chosen from whatever a supplier had on the shelf that week.
Every Rayson material on your floor or roof has a published technical data sheet. You can read what went in, and so can your consultant.
Rayson warrants the material as its maker. The authorised applicator, an independent company that contracts with you, warrants the workmanship. Each warranty is issued by the company responsible for it.
The products, data sheets and application methods are the ones Rayson publishes in Singapore. Nothing is rebadged for Malaysia.
Contractors and facility teams buy the same materials direct from the maker, with application guidance. The applicator is there when you want the job done for you.
Each with the Rayson layers it uses
All Rayson products ↗Factory, warehouse, car park, showroom and home floors in the Klang Valley, with the Rayson system named for the traffic.
Storage halls, workshops and garages: FloorGuard R50, two coats. Hot washdown: PurScreed PC70. Showrooms: R50 under UraForce WB58.
Quoted after inspectionService bays, wash bays and car showrooms: hard-wearing epoxy in the workshop, a colour-stable finish in the showroom.
Wash bays and ramps: R50 broadcast with aggregate. Showrooms: UraForce WB58 topcoat over R50. Heaviest bays: LevelShield SL120.
Quoted after inspectionForklift aisles, racking zones and loading bays in warehouses and distribution centres, in self-levelling or roller-applied epoxy.
Racking and storage zones: FloorGuard R50 roller coats. Heavy traffic with spillage: PurScreed PC70.
Quoted after inspectionYes. Order through Rayson Malaysia (Epovex Coatings Sdn. Bhd.) by WhatsApp or the form; supply and delivery are confirmed for each order, with the data sheets.
The data sheets give a final cure of seven days. Rayson or the applicator tells you when the floor can take cars in your conditions; in cool weather it takes longer.
Ventilate the space, wear gloves and eye protection, keep children and pets away while it cures, and follow the safety data sheet that comes with the material.
Over sound, well-bonded old epoxy, yes, after grinding: PrimeBond E20 lists sound existing epoxy flooring. Over ordinary floor paint, no: grind it off to the concrete.
Rayson warrants the material as its maker when it is applied to the data sheet. A do-it-yourself job carries no workmanship warranty; an applicator’s job does.
Tell us what the surface is, where it is and what it has to withstand. Rayson replies with a system recommendation; for installation, the applicator for your area in Johor, Kuala Lumpur or Penang is introduced to quote the job.
Malaysia launch: 1 March 2027. Enquiries are welcome now; supply, site assessment and installation timing are confirmed for each project.