Coloured low-odour floor finish
- Prime or seal with Rayson HydroShield WE40 (system pairing to be confirmed by the Rayson technical team)
- Apply minimum 2 coats of Rayson UraForce WB58, stripe-coating edges by brush
Rayson UraForce · Polyurethane
Rayson UraForce WB58
Rayson UraForce WB58 is a two-component, water-based aliphatic polyurethane dispersion topcoat, crosslinked with a PUR hardener, for abrasion-resistant coloured finishes on concrete, metal and mineral surfaces.
ConcreteWalls TDS RY-TDS-703
Best for
Best for coloured, UV-resistant floor and wall finishes in schools, offices and retail spaces where water-based application is required.
UraForce WB58 brings aliphatic polyurethane performance to water-based application. The pigmented polyurethane dispersion crosslinks with its PUR hardener into a film with excellent abrasion resistance, low dirt pick-up, good water repellence and pencil hardness above H — a working finish that dustproofs and protects the substrate.
It is supplied in colours including grey, and adheres to mechanically prepared concrete, metal, stone and limestone. Typical duties are UV-resistant coloured coatings for concrete floors, hygienic washable coatings for walls, and non-yellowing topcoat finishes across commercial and educational interiors.
Mix ratio is 9:1 by weight with a pot life of 1–2 hours, applied by brush or roller in a minimum of two coats.
In Malaysia
Supplied by Epovex Coatings Sdn. Bhd., Company No. 202601042128 (1704223-A). The Malaysia launch is scheduled for 1 March 2027; confirm availability and lead time for your project. Installation through an authorised applicator in Johor, Kuala Lumpur or Penang introduced by Rayson, who quotes and warrants the workmanship, or by your own crew with Rayson’s application guidance.
Send an enquiryKey benefits
- Water-based aliphatic PU — UV-resistant, non-yellowing coloured finish
- Excellent abrasion resistance and low dirt pick-up
- Good water repellence with pencil hardness above H
- Hygienic, washable finish for walls and floors
Recommended uses
- UV-resistant coloured coatings for concrete
- Topcoat finishes on hard surfaces such as stone and limestone
- Hygienic coatings for walls and floors
- Non-yellowing, high-abrasion-resistance finishes in commercial interiors
Application
- Short-bristled brush
- Roller
| Specification | Data sheet value |
|---|---|
| Mixing | Two pre-weighed parts, mix ratio 9:1 by weight; stir parts separately, combine and mix with a slow-speed drill and paddle for 1–2 minutes; pot life 1–2 hours |
| Drying and curing | Surface dry 6 hours at 25 °C |
| Pack sizes | Part A 4 Lt or 18 Lt pail + Part B 1 Lt or 2 Lt pail |
Typical systems
Limitations
- Minimum substrate temperature 5 °C; minimum mixing temperature 10 °C; minimum curing temperature 5 °C
- Mixed material must be used within its 1–2 hour pot life; cures faster in hot weather and in large batches
- Hardener shelf life is shorter than the base and moisture-sensitive — store sealed and dry
- Thin-film topcoat — requires a sound, sealed substrate or system beneath
Not suitable for
- Heavy industrial traffic without a suitable body coat beneath
- Immersion or chemical containment service
- Filling or levelling defective substrates — it is a thin decorative-protective film
Jobs and industries
Jobs that use Rayson UraForce WB58
Rayson-authorised applicators in Johor, Kuala Lumpur and Penang install Rayson UraForce WB58 on these jobs and in these industries; its layer is marked in each build-up. Each page shows how the work runs, what to send for a quotation and what decides the price.
Jobs in Johor
01 Rayson system
Home epoxy flooring
Garages, kitchens, living rooms and porches: plain coloured epoxy by Rayson, IFS metallic and flake finishes over Rayson primer.
- UraForce WB58 polyurethane topcoat
- FloorGuard R50 epoxy in your colour
- PrimeBond E20 epoxy primer
- Concrete floor, keyed and repaired
Metallic and flake finishes: IFS Metallic Epoxy or Epoxy Flake Lining, over the same primer.
Quoted after inspection 02 Rayson system
Shop, café and showroom floors
Seamless, cleanable floors done overnight or between tenancies, with colour that lasts under daylight.
- UraForce WB58 topcoat, colour-stable in daylight
- FloorGuard R50 epoxy in the shop’s colour
- PrimeBond E20 epoxy primer
- Concrete floor, degreased and keyed
GripSafe AP12 texture at the entrance and wet zones.
Quoted after inspection 03 Rayson system
Furniture factory floors
Machining halls, timber stores, packing and container loading, finishing lines and buyer showrooms in the furniture factories of Muar and Batu Pahat.
- LevelShield SL120 self-levelling epoxy
- PrimeBond E20 epoxy primer
- Concrete slab, ground, joints and cracks repaired
Timber and board stores: FloorGuard R50. Showroom: R50 under UraForce WB58, or an IFS finish. Finishing lines: after the chemical check.
Quoted after inspectionJobs in Kuala Lumpur and Selangor
Kuala Lumpur and Selangor ↗ 04 Rayson system
Epoxy flooring in KL and Selangor
Factory, warehouse, car park, showroom and home floors in the Klang Valley, with the Rayson system named for the traffic.
- LevelShield SL120 in the forklift aisles and loading bays
- PrimeBond E20 epoxy primer
- Factory slab, moisture- and bond-tested, ground
Storage halls, workshops and garages: FloorGuard R50, two coats. Hot washdown: PurScreed PC70. Showrooms: R50 under UraForce WB58.
Quoted after inspectionBy industry, across Malaysia
Industries we cover ↗ 05 Rayson system
Food and beverage factory floors
Hot washdown, wet process and dry store floors for food and beverage plants, with coves and drains detailed.
- PurScreed PC70 PU-cement screed, 1.5–3 mm
- Concrete slab, prepared, coves and drains detailed
Dry stores and packing: FloorGuard R50 or LevelShield SL120 over PrimeBond E20. Walls: UraForce WB58.
Quoted after inspection 06 Rayson system
Commercial and central kitchen floors
Cooking lines, dishwash and prep areas in central, hotel and restaurant kitchens: PU-cement where it is hot, epoxy where it is dry.
- PurScreed PC70 PU-cement screed, 1.5–3 mm
- Slab, old tiles removed, coves and drains detailed
Cold prep, stores and corridors: FloorGuard R50 broadcast with aggregate, over PrimeBond E20.
Quoted after inspection 07 Rayson system
Workshop and showroom floors
Service bays, wash bays and car showrooms: hard-wearing epoxy in the workshop, a colour-stable finish in the showroom.
- FloorGuard R50 epoxy, two coats
- PrimeBond E20 epoxy primer
- Concrete floor, degreased, ground and repaired
Wash bays and ramps: R50 broadcast with aggregate. Showrooms: UraForce WB58 topcoat over R50. Heaviest bays: LevelShield SL120.
Quoted after inspection 08 Rayson system
Pharmaceutical and medical device plant floors
Production rooms, clean rooms, device assembly, washdown rooms and stores in pharmaceutical and medical device plants, with smooth, cleanable floors and walls.
- LevelShield SL120 self-levelling epoxy, coved at the walls
- PrimeBond E20 epoxy primer
- Concrete slab, prepared and moisture-tested
Walls: UraForce WB58. ESD assembly: StaticGuard CX90. Washdown rooms: PurScreed PC70.
Quoted after inspection 09 Rayson system
Hospital, clinic and care home floors
Corridors, service areas, kitchens, laundries, wet rooms, ramps and car parks in hospitals, clinics and care homes, laid in occupied buildings.
- Tiles, re-laid after the ponding test
- Tile bed
- SealForce WB20, two coats, turned up the walls
- Screed to falls
- Floor slab
Corridors and service areas: LevelShield SL120 or FloorGuard R50. Kitchens and laundries: PurScreed PC70. Walls: UraForce WB58.
Quoted after inspection 10 Rayson system
School and kindergarten floors
Classrooms, corridors, halls, walkways, playgrounds, toilets, canteens and roofs in schools and kindergartens, done in the school holidays.
- UraForce WB58 topcoat, colour-stable
- FloorGuard R50 epoxy in a colour from the range
- PrimeBond E20 epoxy primer
- Concrete floor, keyed and repaired
Walkways, ramps and playgrounds: GripSafe AP12. Toilets: SealForce WB20 under the tiles.
Quoted after inspection The practical details
Rayson UraForce WB58: questions people ask
Why choose WB58 over a solvent-based PU?
Water-based application: it can go into occupied and enclosed spaces without solvent odour, while keeping the abrasion resistance and UV performance of aliphatic PU chemistry.
What colours are available?
It is supplied pigmented, with grey among the colours offered. Confirm the current colour range with our sales team.
How many coats does a floor need?
A minimum of two coats by brush or roller, stripe-coating edges first.
What is the coverage rate?
Confirm coverage with our technical team when planning quantities.
How should the hardener be stored?
Sealed, dry and under cover — the PUR hardener is moisture-sensitive and has a shorter shelf life than the base component.
Start a conversation / ↗
Send the job, or ask for materials
Tell us what the surface is, where it is and what it has to withstand. Rayson replies with a system recommendation; for installation, the applicator for your area in Johor, Kuala Lumpur or Penang is introduced to quote the job.
Malaysia launch: 1 March 2027. Enquiries are welcome now; supply, site assessment and installation timing are confirmed for each project.